Right now I'm Offline I have made 1 post
I joined November 2020
I've received 1 like
I currently have no messenger contact information filled out.
I currently have no social network information filled out.
Hello Folks,
since i swapped my 3700X with a 5950X the RGB Fusion Software won't detect my G.SKill Trident Z Neo RAM so i can't control it anymore, therefore it will stay on in standby all the time.
Board: Aorus Master X570
BIOS: F31e
I already installed a fresh Windows just to see if that helps, but no. Gigabyte, do something!
Right now I'm Offline I have made 41 posts
I joined November 2020
I've received 1 like
I currently have no messenger contact information filled out.
I currently have no social network information filled out.
When did you upgrade to F31e? Was it the same time as the 5950x or did you BIOS flash and test that change fully before moving to the 5950x? And which build of RGB Fusion 2.0 are you using?
I have TONS of problems with my x570 Master Rev 1.1 on F31e and RGB fusion. RGB Fusion 2.0 build 20.1015.1 won't run at all for me (this is the newest one from Gigabyte's server). I downgraded to RGB Fusion 2.0 build 19.1030.1 and I can at least control my mobo RGB with it, but it has stability problems. It will crash and when the software crashes it takes down Windows with it.
I'm not going to put a lot of effort into digging into this until F31 moves out of BETA as I kind of expect problems with a BETA BIOS.
Right now I'm Offline I have made 7 posts
I joined April 2017
My gender is Male
I currently have no messenger contact information filled out.
I currently have no social network information filled out.
Thank God i found this thread. I was going crazy trying to fix this today with no luck.
I have the exact same issue. I updated my BIOS to F31e and then installed my 5950X and now i cant control my G.SKill Neo RAM with either RGB Fusion or the G.Skill RGB Software. I was almost going to install a fresh copy of Windows but i was to lazy today.
Right now I'm Offline I have made 26 posts
I joined August 2019
I've received 2 likes
I currently have no messenger contact information filled out.
I currently have no social network information filled out.
Same issue for me with F31E and 5800x, this software RGB fusion is absolute garbage, also the HDD spinning problem persists over an year now and the support say "they are working on it". Will never buy Gigabyte ever again, their attitude towards their software is total bull"xxx".
There is quite a large topic on the forum about it you can read it, but basically RGB fusion check for "RGB" hdd's quite often so it wakes sleeping hdd's which are not in use at the moment, and it is quite annoying when this happens every 5 min as mechanical drives spin quite loudly, not to mention its not very healthy for your hdd.
Right now I'm Offline I have made 7 posts
I joined April 2017
My gender is Male
I currently have no messenger contact information filled out.
I currently have no social network information filled out.
The issue is now fixed for me with a new version of RGB Fusion B20.1113.1 RGB Fusion Note: For AMD Ryzen 5000 series processors support OS: Windows 10 64bit B20.1113.1
Right now I'm Offline I have made 5 posts
I joined November 2020
I've received 1 like
I currently have no messenger contact information filled out.
I currently have no social network information filled out.
Now mine is not working again. I can't even connect to my motherboard :/
I did a format c: so any other program wouldn't mess with the detection, but after a hour on the fresh installed windows the RGBFusion is not detecting motherboard or RAM. I would say, that it worked just after install off RGBFusion on the fresh installed Windows 10 Pro. But after an hour, it stops
Right now I'm Offline I have made 68 posts
I joined April 2020
I've received 5 likes
I currently have no messenger contact information filled out.
I currently have no social network information filled out.
I haven't had any version of RGB fusion to recognize my G-Skill memory since the last Windows 10 fall update. It will recognize it one of 10 boots maybe. Contacted Gigabyte, no help! Some versions including the most resent one 3.20.1113.1 says it requires Microsoft C++ 2015 redistributable, try to install that version, but windows will not allow saying a newer version is already installed. Not sure if that has anything to do with it. Tried uninstalling many versions with a clean install, no help! I think this is a Windows problem.
Nov 21, 2020 0:20:32 GMT -8 | abn505 likes this | via mobile
I haven't had any version of RGB fusion to recognize my G-Skill memory since the last Windows 10 fall update. It will recognize it one of 10 boots maybe. Contacted Gigabyte, no help! Some versions including the most resent one 3.20.1113.1 says it requires Microsoft C++ 2015 redistributable, try to install that version, but windows will not allow saying a newer version is already installed. Not sure if that has anything to do with it. Tried uninstalling many versions with a clean install, no help! I think this is a Windows problem.
Maybe it is a Windows problem, but maybe gigabyte is using old software version for the program, and therefor its not working ;/ I can't figure out how to force RGBFusion to use the 2015 C++
Right now I'm Offline I have made 41 posts
I joined November 2020
I've received 1 like
I currently have no messenger contact information filled out.
I currently have no social network information filled out.
This is not a windows problem. This is a gigabyte problem. They are releasing a software package that relies on an older redistributable. This is *yet again* another instance of their incompetence. It appears they are developing on older versions of Win10, not the current distribution.
To get the newest version of RGB Fusion installed, I had to uninstall all my C++ 2015 redistributable packages, disable windows updates, reboot, reinstall RGB Fusion let it fail to get the appropriate error message, find the old redistributable they use with that package, install that old distribution manually, then reinstall RGB fusion, this time it worked, reboot and everything is OK now.
alekhinescat wrote: Jul 20, 2021 15:03:25 GMT -8 I have the same issue.
s2h wrote: Jul 19, 2021 8:39:05 GMT -8 AMD Picasso is king !
davicom wrote: Jul 19, 2021 2:45:02 GMT -8 Hi guys thanks for your support, I plug out rtx and nvme, today I'm going to try with another nvme pci 3.0 and we'll see what happens
bamainark wrote: Jul 18, 2021 18:22:47 GMT -8 kshipper. Ugggg Good catch. BTW he's got a thread on the Z590 forum*
kshipper wrote: Jul 18, 2021 17:27:10 GMT -8 I assume you meant you had a 600k? I have not seen a 500k
davicom wrote: Jul 18, 2021 0:01:30 GMT -8 I tried everything on bios, bifurcation on 8,4,4 and 8,8 with my rtx 3080 ti but without success; force pcie gen4; ahci; nothing seems to solve: is stationary on [email protected] Processor is Intel Core i5 11500K. I would really appreciate some suggestion. Thanks
davicom wrote: Jul 17, 2021 23:58:01 GMT -8 Hi all, I'm really exhaust to try get Samsung NVME 980 Pro run at gen 4.0 on my Z590 Aorus Ultra, it matches just 3.0
kshipper wrote: Jul 16, 2021 10:53:12 GMT -8 amsss: I suggest you pick a category on the left and make a post. This area is limited to 256 characters.
amsss wrote: Jul 16, 2021 9:24:15 GMT -8 hello. is anyone there? i really need help
marson wrote: Jul 14, 2021 9:28:20 GMT -8 Did you read the thread I linked you to? That goes much deeper. Can't go very deep in the 256 characters we're limited to here. Try starting a new thread and asking a more specific question that reflects what still isn't clear.
magrw1033 wrote: Jul 13, 2021 14:12:29 GMT -8 Thx. But that just restates the words of the manual. I was looking for something deeper.
segedite wrote: Jul 9, 2021 12:57:07 GMT -8 I have these two messages: BIOS Mode. Legacy - Secure Boot: Registry not found ... how do I enable the BIOS? on AORUS Z390 PRO ... BIOS Is F12. *
magrw1033 wrote: Jul 9, 2021 10:53:33 GMT -8 What does the cpu and memory status led's really mean?
greggg wrote: Jul 6, 2021 13:00:20 GMT -8 Just stuck a new bios chip (easy job) into my X470 so now I have the very latest bios chip needed (for a Ryzen 5 5600x). Didn't want to try this 'bios update' business because there are too many unhappy stories out there.
gritsmelike wrote: Jul 6, 2021 10:13:23 GMT -8 Thank you, bigdave systems info indicates an un-allow DMA bus device detected have fresh install W10 OEM 21H1 Z490 UD Me built. I didnt have a frt. header E-type for the USB C added card to pcie 3.0x4 slot to convert. sys installed the driver. HUM
