Feb 8, 2019 11:15:44 GMT -8

Reply Quote | Like

Xdeath666
Guest

Hi ! I have a 1080Ti since 1 year about and no problem at all. My temp are 60-75 max also. But since little time i have some little red spiral thing appear and disapear very fast. Its always when i play or not movie does it too. Hmm.... My drivers are up and clean install also. I play game like Re2R and FF14. Theres things are pretty strange because its come and its get out at random. No crash. I have some impression than my performance drop like 1 or 2% on the same game. Sluttering in many game too with kind of Vsync problem....

So what wrong with the beast ? Driver ? Hot card ? (75max is good no?) My plug is ok and my comp is a 8700k rig.

Is this VRAM problem ? I take these ticket just for have the good point. thx

chong83 wrote: Feb 16, 2019 7:32:57 GMT -8
check the task manager which software progress use high CPU or SSD

totallypissedoff wrote: Feb 16, 2019 5:02:17 GMT -8
grichie Try downloading, and installing the Aorus Graphics Engine directly from the Gigabyte website. Installing from the disk is not the best idea, as it is most likely an older version of the software.

dvojinov wrote: Feb 14, 2019 2:59:58 GMT -8
hello , does someone knows where to download older version of Aours VGA tool 1.52?

vanowm wrote: Feb 13, 2019 16:12:37 GMT -8
mechanicman91, you need connect your monitor to motherboard, enter bios and set PCI-E graphic card as primary.

bigdave wrote: Feb 13, 2019 12:41:06 GMT -8
spaceweasel,Use the NVIDIA Control Panel -->Help-->system information.

spaceweasel wrote: Feb 13, 2019 11:47:46 GMT -8
I have an Aorus RTX280 Extreme card. What's the easiest way to check firmware version?

mechanicman91 wrote: Feb 12, 2019 20:02:48 GMT -8
i just put together a B450I ryzen 2400G system with 16gb of G Skill ddr4 3200 and a 970 evo. the pc will turn on, but the monitor wont detect until it is past bios. just curious if any of y'all have seen this before.

dimentograven wrote: Feb 12, 2019 17:55:21 GMT -8
Is there any way to turn Easy Raid off once activated? I turned it on thinking I could setup two NVME drives in a stripe, but when I enabled Easy Raid, I found the NVME drives don't show up in the list, and th the existing SATA SSD no longer properly boot

karambit wrote: Feb 12, 2019 10:09:32 GMT -8
Are the mounting holes for an EK Monoblock for the newer Z390( Ultra, pro or Designare)in the same position and series as the Z37 Aorus Gaming 7 ?

yuki wrote: Feb 12, 2019 4:30:22 GMT -8
I'm having issues with removing the SSD Screw from the Heatsink, Using the Z390 Board. Any tips removing the screw? It feels like they are super tight

galving wrote: Feb 12, 2019 3:14:12 GMT -8
mmanfroni I'm having similar issues. on the z390 xtreme with g.skill royal 4266mhz. system doesn't boot with xmp enabled

Dragzilla66 wrote: Feb 11, 2019 15:12:56 GMT -8
Hello fellow Gigabyte users.

warpigs wrote: Feb 9, 2019 20:56:42 GMT -8
Hello All, New build getting A6 error code..Gigabyte Z390 Aorus Ultra v 1.0..I tried with my 2 M.2 SSD's out and still get as well. Any advise? Thank you in advance.

hannanfix wrote: Feb 9, 2019 11:19:51 GMT -8
My Motherboard is Z370 AORUS Gaming 5. Processor 9700k. Samsung 970 M.2 NVME and ADATA XPG M.2 NVME. Graphics XFX RX 580.

I installed GC-ALPINE RIDGE (rev. 1.0) but in Bios it did not show. I update and downgrade BIOS no hope. Then I Disconnected MY All *

hannanfix wrote: Feb 9, 2019 11:09:21 GMT -8
Gigabyte Z370 AORUS Gaming 5 My Board. After upgrading BIOS F12c My Hackintosh is unable to load. I am a very serious Ex pert in Hackintosh. Then I downgrade and F10 and everything OK.

grichie wrote: Feb 9, 2019 7:00:57 GMT -8
I just purchased and installed a new gigabyte Geforce 1050 and installed the software from the included disk. I have not been able to find or access the aorus engine to make adjustments to the graphics card.

Can anyone tell me how to find this feature? *

vanowm wrote: Feb 9, 2019 6:32:09 GMT -8
mmanfroni, contact tech support. If the ram in QVL list they will need fix their f-up in bios.

mmanfroni wrote: Feb 8, 2019 20:07:19 GMT -8
hi guys, someone use 4266mhz rams? i have aorus master z390 and at max frequence system is instable/dont boot, at 4000 is stable.

vanowm wrote: Feb 8, 2019 15:25:27 GMT -8
joaomonteiro, try another power supply, then remove/unplug everything except power supply, then add cpu, next ram. Test it after each step, If not changes between all these steps, then I'd say it's dead.

joaomonteiro wrote: Feb 8, 2019 4:24:02 GMT -8
Hello everyone. I need some help about my Gigabyte GA-X58a-UD7. i died on me and i can only see the poder and the clear cmos light on. before this i only saw all led's lid up and error code 88 for brief second. is it really dead or is it salvagable?