Sept 9, 2018 12:20:44 GMT -8

Reply Quote | Like

	maxiuca	Right now I'm Offline I have made 1 post I joined September 2018		I currently have no messenger contact information filled out.	I currently have no social network information filled out.

I just got the new GC-TITAN RIDGE (rev. 1.0) TB3 expansion card and I'm confused by the USB 2.0/1.1 connector...
What is it this connection for? What does it do? What functionality does it provide? Why is it there?

Does it need to be connected for TB3 to work properly?

I only have one USB 2.0 header on my Mobo and it's already in use.

Edited Sept 9, 2018 12:21:47 GMT -8 by maxiuca

Sept 20, 2018 12:33:46 GMT -8

Reply Quote | Like

	nismomismo	Right now I'm Offline I have made 1 post I joined September 2018		I currently have no messenger contact information filled out.	I currently have no social network information filled out.

I have the same problem as maxiuca.

The USB header on my Mobo is already in use.

Does it need to be connected for me to be able to make the Thunderbolt 3 work?

djbillyd wrote: Feb 22, 2019 13:51:02 GMT -8
So I guess nobody knows what I'm talking about, huh?

bigdave wrote: Feb 22, 2019 7:15:14 GMT -8
c2Lt357357, I have seen issues where certain dimms will cause graphic adapter issues. You might look for a BIOS update or use different dimms. Check the QVL and use matching dimms.

c2lt357357 wrote: Feb 21, 2019 10:35:16 GMT -8
Mobo:GA-970A-DS3P (2.1).I have 2-8GB sticks installed. If add 2-4GB sticks, when Windows loads, device manager reports Code 43 for display adapter. Take the additional RAM out and works again. I've tried memory configs where same capacity is in slots 1/2,

djbillyd wrote: Feb 20, 2019 20:29:39 GMT -8
I can boot to the DVD, and press a key to start the disc. But after that, I get nothing but the scramble thingy I told you about earlier.

djbillyd wrote: Feb 20, 2019 20:28:13 GMT -8
I got an issue. I have a B450 that I just installed. I have a Radeon 5450 video card for display. The screen has a scrambled pattern that keeps coming up, then it goes away and leaves a blank screen. The board will post on start up, and I can go into BIOS.

shtrebanmax wrote: Feb 20, 2019 9:01:37 GMT -8
Hi, guys.I need help from an American. If you are interested, write to me in telegram @artur_Svetlov

dalaibrahma wrote: Feb 19, 2019 11:32:27 GMT -8
Why I can not go cpu Vid more than 1,365V in X470 aoug ?? Is there biosmod for it?

dalaibrahma wrote: Feb 19, 2019 11:30:46 GMT -8
Hi, Guys! I am Brazilian.. Sorry my porr English.

chong83 wrote: Feb 16, 2019 7:32:57 GMT -8
check the task manager which software progress use high CPU or SSD

totallypissedoff wrote: Feb 16, 2019 5:02:17 GMT -8
grichie Try downloading, and installing the Aorus Graphics Engine directly from the Gigabyte website. Installing from the disk is not the best idea, as it is most likely an older version of the software.

dvojinov wrote: Feb 14, 2019 2:59:58 GMT -8
hello , does someone knows where to download older version of Aours VGA tool 1.52?

vanowm wrote: Feb 13, 2019 16:12:37 GMT -8
mechanicman91, you need connect your monitor to motherboard, enter bios and set PCI-E graphic card as primary.

bigdave wrote: Feb 13, 2019 12:41:06 GMT -8
spaceweasel,Use the NVIDIA Control Panel -->Help-->system information.

spaceweasel wrote: Feb 13, 2019 11:47:46 GMT -8
I have an Aorus RTX280 Extreme card. What's the easiest way to check firmware version?

mechanicman91 wrote: Feb 12, 2019 20:02:48 GMT -8
i just put together a B450I ryzen 2400G system with 16gb of G Skill ddr4 3200 and a 970 evo. the pc will turn on, but the monitor wont detect until it is past bios. just curious if any of y'all have seen this before.

dimentograven wrote: Feb 12, 2019 17:55:21 GMT -8
Is there any way to turn Easy Raid off once activated? I turned it on thinking I could setup two NVME drives in a stripe, but when I enabled Easy Raid, I found the NVME drives don't show up in the list, and th the existing SATA SSD no longer properly boot

karambit wrote: Feb 12, 2019 10:09:32 GMT -8
Are the mounting holes for an EK Monoblock for the newer Z390( Ultra, pro or Designare)in the same position and series as the Z37 Aorus Gaming 7 ?

yuki wrote: Feb 12, 2019 4:30:22 GMT -8
I'm having issues with removing the SSD Screw from the Heatsink, Using the Z390 Board. Any tips removing the screw? It feels like they are super tight

galving wrote: Feb 12, 2019 3:14:12 GMT -8
mmanfroni I'm having similar issues. on the z390 xtreme with g.skill royal 4266mhz. system doesn't boot with xmp enabled

Dragzilla66 wrote: Feb 11, 2019 15:12:56 GMT -8
Hello fellow Gigabyte users.